Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Orange: What to Know First
Linear gate installation in Orange typically runs $1,850 to $6,400 for a complete driveway system, depending on whether you’re automating an existing gate or starting from scratch with new steel and a new operator. Most installations are completed in one visit, with a written price agreed before we turn a single bolt. Call (707) 754-0878 for a free estimate on your Linear gate.
This page is for Orange homeowners who already own a Linear operator or are weighing one against other brands, and want the installation done by people who work on these units every week. As an independent Linear service provider, we’re not tied to the manufacturer, which means we tell you the truth about what’s worth fixing and what isn’t. If your gate hasn’t moved since the Clinton administration, we’ll tell you that too, and exactly what it will take to get it swinging or sliding again.
Victor Salinas grew up in the Friendly Hills area of Orange, not far from where Chapman Avenue meets the older neighborhoods where wrought-iron fences have been a fixture for decades. He’s been doing this work for over 42 years, and he still answers the phone.
How Linear Products Fail - and How We Fix Them
- Linear LRA and LRA-S series swing arms: stripped gear teeth from wind loading. Orange gets real Santa Ana gusts that catch a solid gate panel like a sail. The plastic reduction gear inside the LRA operator strips first, before the metal parts fail. The symptom is a motor that hums but won’t move the gate. We replace the gear with a factory-spec part and set the force limits correctly so the next gust doesn’t repeat the job in six months.
- Linear SL series slide operators: limit switch drift. The SL series uses mechanical limit switches that can creep over time, especially with the fine dust and pollen that settles on everything in Orange. The gate starts stopping six inches short or overrunning the end stops. We reset and lock the limits, then clean and seal the switch housing. If the switch contacts are worn, we replace them rather than letting the operator slam the gate into the stop and bend the track.
- Linear actuator arms on pedestrian gates: bent from manual forcing. When a Linear actuator arm is mounted on a pedestrian gate, someone always tries to push or pull the gate open by hand at least once. The arm bends or the internal screw jams. We straighten or replace the arm, but more importantly we install a proper gate stop and a manual release that’s actually reachable, so the next visitor doesn’t treat it like a barn door.
- Older Linear APeX and LSO series: dead control boards from power surges. Orange’s older neighborhoods still have overhead utility lines and the occasional brownout or surge. Linear control boards are sensitive, and a nearby lightning strike or transformer event can take the board out while the motor stays perfect. We test the board independently before condemning it, and we install surge protection on the circuit when we replace it, so the repair lasts.
- Linear remote and receiver mismatch: frequency drift on older 318 MHz units. We see this constantly on gates that were installed 15-plus years ago. The homeowner has a Linear opener that works at the keypad but not from the car, and they assume the remote battery is dead. Often the receiver has drifted off frequency. We can re-tune or replace the receiver, and if the unit is too old to hold a clean signal, we’ll say so plainly rather than selling you another remote that won’t work either.
Our Linear Gate Installation Process
- 1
Call and describe the job. A live person answers, 24 hours a day, seven days a week. No voicemail tree. We ask what kind of gate you have, what the Linear unit is doing or not doing, and we schedule a time. You get the $0 estimate, not a service fee that gets rolled into the bill.
- 2
On-site assessment. We check the gate itself first: hinges, posts, wheels, track. A Linear operator can only be as good as the gate it’s attached to. If the gate drags or the post is leaning, the new operator won’t last and we’ll tell you before we quote anything.
- 3
Written quote, agreed before work. You get a line-item price for the operator, the mounting hardware, the power run if needed, and the labor. We don’t start until you approve the number, and the number doesn’t change after we start.
- 4
Installation. We mount and level the Linear unit, run the wiring, install safety edges and photo eyes where required by code, and set the force and travel limits. We use factory or quality aftermarket parts, and we tell you which is which and why.
- 5
Test and teach. We cycle the gate several times under load, adjust the clutch and limits, then walk you through the keypad, remotes, and manual release. If you have a question a month from now, you’ll get the same person on the phone.
- 6
Cleanup and the written guarantee. We remove the old parts and packaging. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right. No paperwork, no arguing.
What Linear Gate Installation Costs in Orange
Here’s what we tell Orange homeowners to expect for common Linear scenarios:
- Replace an existing Linear operator with a new Linear unit: $1,850 to $2,900, including mounting, wiring, and programming. If your gate is in good shape and the existing pad is usable, this is a straight swap.
- Full installation: new steel gate plus Linear operator: $3,400 to $6,400 depending on gate size, material, and whether it’s a swing or slide configuration. Double driveway gates run higher than single panels.
- Pedestrian gate with Linear actuator and keypad: $1,400 to $2,300, including the gate, post reinforcement, actuator, and keypad.
- Replacing a dead Linear control board or gear set on an existing installation: $280 to $650, parts included. We quote this separately from full replacement and we’ll tell you honestly if the unit is worth repairing.
What moves the price: gate size and weight, whether the post or track needs work, distance from the nearest electrical panel, and whether you want a battery backup or additional remotes. We settle the number before we start, and it’s the number on the bill. Call (707) 754-0878 for a free estimate on your specific setup.
Why Orange Homeowners Call Ironworks Gate Co. for Linear Work
We’ve been doing this for over 42 years. The company was founded in 1984, and we plan to be in Orange for another forty. The homeowner who calls us is usually not shopping for the lowest bid. They’ve had a gate guy before, and that guy didn’t come back. They want the job done once, correctly, and guaranteed in writing.
Every Linear job we take is covered by the 90-Day Done Right Promise, in writing, on every job. No hassle, no arguing, no exceptions. If the gate isn’t right, we come back. That’s the Keystone Standard, and it applies to every job we do, from a hinge replacement to a full automated gate.
We’re trained and equipped on nine gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If we find a Ghost Controls receiver or a Mighty Mule arm on the property while we’re working on your Linear system, we know what to do with it. Background-checked, uniformed technicians on every job, working in your home the way they’d work in their own mother’s driveway.
FAQs
Yes, in most cases we can mount a Linear operator on an existing gate, provided the gate itself is sound, the posts are plumb, and there’s a safe place to mount the operator and run power. We inspect the gate first and tell you if any structural work needs to happen before the operator goes on. Call (707) 754-0878 for a free assessment.
We use genuine Linear parts whenever available and warranted, and we use quality aftermarket parts when they are functionally identical or better and save you money without cutting corners. We tell you which one we’re quoting and why, before any work begins, so you’re never surprised by what’s on the invoice.
If your Linear operator is under the manufacturer’s warranty, our installation does not void it, and we’ll do the warranty-required paperwork if a part fails under warranty. As an independent service provider, we don’t administer Linear’s warranty, but we handle the labor and coordination so you don’t have to fight with a phone menu.
Most Linear gate installations are scheduled and completed in one visit, and we answer the phone live 24 hours a day, seven days a week. If you have a gate that’s stuck open, we’ll tell you on the phone what it sounds like and get a technician to you as fast as the schedule allows that day or the next. Call (707) 754-0878 and you’ll talk to a person who knows gates, not a call center.
If the operator is under ten years old and the failure is a single part like a gear, capacitor, or control board, repair usually makes sense, typically $280 to $650. If the unit is over fifteen years old, has multiple failing parts, or the gate itself is heavy enough to strain the motor, replacement is usually the smarter money. We’ll give you a straight answer and both prices before you decide.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Orange and nearby areas.